Reversible Stripes Scarf

With an itch to make a scarf, I found myself happily lost in the pages of Barbara Walker's seminal "Treasuries" of stitch patterns. Intrigued by the rhythms and possibilities of her slip stitch patterns, I think I tried them all. And then I finally combined a couple, a bit of Woven Stitch and a dash of Linen Stitch and voila, a reversible stripe!

This magical world of slip stitches has me firmly in its clutches. How else could there be a simple knit fabric with so much complexity and fascination?!? One side of this stitch pattern is smooth and flat, seemingly woven, with impeccably thin horizontal pinstripes; while the other side is textured in deep, hearty ridges, running in vertical stripes like a knotted tweed.

When wrapped, folded, and tucked around your neck, this scarf is delightfully dizzying! It achieves all I hoped for and more. No curled edges and two sides that aren't just both presentable, but whose contrast in pattern and texture actually enliven and complement one another.

In the spirit of the love and generosity of Valentine's Day, I knit up my scarf in Jade Sapphire's unparalleled Zageo 6 Ply Cashmere. An elegant yarn for a timeless scarf,  it is amazingly soft and toasty warm. If only I had the heart to actually give it away! --Laura

Update: October 2013

Pictured below, is a new version of the Reversible Stripes Scarf using a combination of Jade Sapphire's Zageo 6 Ply Cashmere and Alchemy's Kozmos, a wonderfully complex yarn that adds texture and shine.

I followed the original pattern (below) with one modification: a cast on of 55 stitches, resulting in a more generous finished dimension of 9 inches wide x 92 inches long. -Laura


You can get all the yarn you'll need for this scarf with our Yarn for Reversible Stripes Scarf kit. Each kit includes either...

Or for the new version...

  • 4 skeins of Alchemy's Kozmos for Yarn A, in the color Silver.
  • 3 skeins of Jade Sapphire's Zageo 6 Ply Cashmere for Yarn B, in the color Ivory.

For the original all-cashmere version, I used the color Pewter for Yarn A and the color Ivory for Yarn B. Pictured below are swatches of nine additional available colorways, each one available as a Yarn for Reversible Stripes Scarf kit!

  • Top Row, from left: Silver Fox (Color A) + Pewter (Color B), Silver Pearl + Cousin Coral, Pink Panther + Silver Pearl
  • Middle Row, from left: Ivory + Pink Panther, Ivory + Silver Pearl, Pewter + Silver Pearl
  • Bottom Row, from left: Ivory + Cousin Coral, Silver Pearl + Silver Fox, Cousin Coral + Pink Panther

For this project, you will also need:


6 stitches = 1 inch in stitch pattern


Original Scarf (all 6 Ply cashmere): 8 inches wide by 72 inches long

New Scarf (6 Ply Cashmere and Kozmos): 9 inches wide x 92 inches long

Swatches: 3 1/2 inches square


If you would like to adjust this pattern for a different width, simply cast on any odd number of stitches.

Slip stitches purl-wise.

Each row in this pattern starts with the instructions to either "Turn" or "Slide" the work:

  • "Turning the work" means to do what you would normally do when knitting rows with a circular needle. That is to say, put the needle in your left hand into your right and the needle in your right hand into your left, and flip the work around so the opposite side is facing you.
  • "Sliding the work" means to keep the same side of the work facing you and to push all the stitches to the right end of the circular needle. Without turning the work, start the new row as you normally would.

You will know that you're doing this right if the yarn you need to complete the next row is magically there waiting for you!



With Yarn A, cast on 49 stitches (or 55 stitches for the 6 Ply/ Kozmos version).

Row 1 (wrong side): Turn, and slip 1 with yarn in front (wyif). With Yarn B, *p1, slip 1 with yarn in back (wyib), repeat from * to end.

Row 2 (wrong side): Slide, and with Yarn A, *p1, slip 1 wyib, repeat from * to last stitch, p1.

Row 3 (right side): Turn, and slip 1 wyib. With Yarn B, *k1, slip 1 wyif, repeat from * to end.

Row 4 (right side): Slide, and with Yarn A, *k1, slip 1 wyif, repeat from * to last stitch, k1.

Repeat Rows 1-4 until piece measure 71 1/4 inches.

Repeat Rows 1-3

In Yarn A, bind off in knit.


With Yarn A, cast on 23 stitches.

Repeat Rows 1-4 until piece measures 2 3/4 inches.

Repeat Rows 1-3

In Yarn A, bind off in knit.


102 Responses to Reversible Stripes Scarf

Click here to add a comment
  1. Claire says:

    Hi There,

    I am having trouble with this pattern. I can do the first 4 rows right, Then when I go to repeat rows 1-4 it starts looking wrong and is not flat, the stiches are lumpy and tight. They look very wrong.. I have tried about 10 times and the same thing keeps happening. Do you have any idea what I could be doing? I am sliding and turning the work and slipping the stiches purl wise. I know I am doing the first 4 rows right because they look perfect, I must just be making a mistake at the part when you start repeating, I cant work out what it is that I am doing wrong.

    • beth says:

      On the very first row of the project, you do not need to Turn.

      • Laura from the Purl Bee says:

        Hi Beth.
        After casting on,turn your work to begin working row one. Once you’ve complete the first tow, to work row two simply slide your stitches to the other end of the needle.
        Let me know if you have any questions!

  2. purl bee says:

    Hi Claire,

    I have a couple questions… Regardless of the bumpy / tightness, are all your horizontal flat stitches on one side and all your vertical bumpy (purl) stitches on the other side? If yes, then this might just be a tension issue. Have you tried changing needle sizes?

    If your horizontal stipes and vertical stripes are not on their respective sides, then this is a larger issue going on. My first guess is that you are knitting with the wrong yarn. Make sure that you are working with one color and then the next, alternating back and forth.

    Can you describe to me how the fabric looks?
    I'd love to help you get this figured out.

  3. Claire says:

    Thank you so much for your reply, I will try with bigger needles and get back to you. I love the look of this scarf. I am determined to get it right :)

  4. Anh says:

    Hi Laura, thank you so much for this beautiful pattern. I mixed white and multicolor yarns and the colors really made this pattern so much fun to knit. I'm at the last row and the bind off makes me nervous. When binding off in knit with color A, do you also knit color B stitches, or do you slip them? I think knitting them makes it uneven. Could you include a picture of that edge?

    Thanks so much!

  5. purl bee says:

    Hi Anh,
    I bound off knitting each stitch. But I definitely encourage you to play around with the bind off edge to find a method that better suits you.

    If you take a look at the picture of the grid of swatches with the horizontal stripes (right side) facing out… you can see the knit bind off edge on those.

    Let me know how it goes for you and if you find that slipping that stitch has a cleaner look!

  6. Donna says:

    I am having trouble purling with the yarn in the back. Is this called Norwegian purl?, or can you purl with yarn in front? Thanks, donna

  7. purl bee says:

    Hi Donna.
    You only slip the one stitch with the yarn in back, then you purl normally, with the yarn in font. I am not sure what a Norwegian purl is, but I am definitely going to look it up now!

    Definitely let me know if you have any more questions on this or other patterns.

  8. JennyV says:

    Fabulous! I am hooked on this elegant and flat fabric!

    Q: is there an easy way to see which row you left off on? I have twice picked this up and not known which side or color to start next. I can always tie a loop before I put my work down. If there is a more apparent way to tell from the knitting, I'd be grateful for your advice!


  9. purl bee says:

    Hi Jenny V.
    Great question! The best way to figure it out (that I found) was to look at the RS of the scarf and see what color the top most horizontal stripe is. That is the color you last worked.

    I ran into the same problem when I first started this scarf.
    Hope this helps.

  10. Mary Jane says:

    I have forgotten how to print just the pattern. thank you

  11. Karen says:

    Both of the links to the kits do not seem to be working today.

  12. purl bee says:

    Hi Karen-

    Thanks so much for bringing this to our attention. The links should be fixed now!



  13. purl bee says:

    Hi Mary Jane-

    We recommend that you copy and paste the instructions and photos you need into a Word or Text doc and print from there.

    Thank you!


  14. Mary Jane says:

    thanks, Molly, Will be so happy to make such an unusual and beautiful scarf

  15. Kat says:

    If I wanted to make the scarf with Kozmos and Jade Sapphire Cashmere but only 72 inches long, could I get away with w skeins of cashmere and 3 skeins of Kozmos?

  16. bette says:

    What cast-on do you recommend?

  17. purl bee says:

    Hi Kat.
    2 skeins of cashmere + 3 skeins of Kozmos will definitely get you to 72 inches long x 8 inches wide!

  18. purl bee says:

    Hi Bette-

    We recommend a long tail cast on.

    Thank you!


  19. meadow says:

    Hi Molly,

    Thank you for this distinct and beautiful pattern. What do you think if I use Blue Sky Alpacas Suri Merino, or Swans Island worsted weight?

  20. purl bee says:

    Hi Meadow.
    Laura here, of Laura's Loop. Weight-wise, Swan's is a wonderful substitution. And texture-wise, Suri Merino is too. The Suri might be a bit on the thick side, so just be sure to swatch first so that you don't end up with too stiff or dense a fabric. Are you combining them? That'd be beautiful.

  21. Catherine says:

    Thank you for this pattern. Instead of coming into purl soho I thought I'd ask you here… My edge is curling up, what's going on and should I stop and solve this or continue? Thanks!

  22. purl bee says:

    Hi Catherine.
    Once the piece is blocked, any scrolled edges should relax. If you are worried if blocking will actually solve the problem, you can always transfer your live stitches onto scrap yarn and steam block (with an iron, hovering above the fabric) what you have to be sure this will solve the problem.

  23. Allison says:

    I'm a relatively new knitter and this is my first slip stitch pattern. Will the slip stitches increase the tension, or am I just holding the yarn too tight because I'm trying way too hard not to mess up? :) The good news it looks just like the pattern…and it's beautiful!

  24. purl bee says:

    Hi Alison.
    That is good news… the fact that you are a new knitter and your fabric looks right is HUGE. Slip stitch patterns can really trip people up. Good job. As for the tension…. I think you've answered your own question. I bet you're just pulling a bit too tight in all the excitement of learning something new. I would maybe swatch a bit more and see if your tension loosens or just practice a bit to see if you get in a rhythm. I would hate if one end of your scarf was a totally different density than the other, which might happen by the time you relax into this stitch pattern.
    So glad you like the pattern.
    Let me know if you have any other questions.

  25. Allison says:

    Hi Laura,

    That's what I was thinking…knit the pattern for a while, get comfortable, then start over again. I don't want a trapezoid instead of a rectangle!

    Thanks so much for your help!

  26. Claire says:

    On row one, if we turn the work, after casting on, when we start row 2, the thread is on the wrong side. What am I doing wrong? Thanks for your help!!!

  27. Sharon says:

    Hi Laura,

    Thank you for sharing this elegant pattern with us.

    I am making several swatches. Everything turns out good except the edges. They are much thicker than the fabric itself, I think I misunderstood the Color B is pulled around the edge and across the first slipped stitch, as was in one of the comments.

    In Row 1 (wrong side): Turn, and slip 1 with YARN in front (wyif). Is this YARN yarn B?

    In Row 3 (right side): Turn, and slip 1 wyib. Is yarn B supposed to be pulled under to be the behind yarn? I hope I am not confusing you.

    One last question: I would like a use a silk and alpaca blend as one of the yarns, but I am not sure whether silk might be stretchy. I saw Alchemy Kozmos is 30% silk, so silk is fine?

    It will be a great project if it all work out.

  28. purl bee says:

    Hi Clair.
    Thanks for writing in.
    This is a single row striped pattern worked flat which means 1. it has to be worked on circular or double pointed needles and 2. you have to slid your stitches to the other end your needles every other row. Be sure to check out the PATTERN NOTES section above. Please write us back if you have any other questions or are still confused on this.

  29. purl bee says:

    Hi Sharon,
    Let's do the easiest question first… Silk and Alpaca would be lovely. Be sure to swatch first to guarantee you're working on appropriate needles (it sounds like you're an avid swatcher which is great!).

    In Row 1 (wrong side): Turn, and slip 1 with YARN in front (wyif)… is with YARN A, then when it says "with YARN B"… you begin working with yarn B. Keeping YARN A in front when slipping that first stitch will help with your edges.

    In Row 3 (right side): Turn, and slip 1 wyib"… this is with YARN A, then when it says "with YARN B" you knit 1… and YARN B is being pulled under the behind yarn, yes, you are correct.

    Please write us back with any more questions!
    I do hope you end up loving the scarf. It's been one of my favorite things to wear these past few months.

  30. Lila says:

    Would this work with kauni effect self striping yarn plus a solid color?

  31. purl bee says:

    Hi Lila-

    We are not familiar with that yarn but as long as you are getting the same gauge as in the pattern it should be fine. If the yarn is self striping you might get a very cool color effect.

    Good luck with the project!


  32. Sharon says:

    Hi Laura,

    Sharon here. After many tries, so far I have one edge, left side of the wrong side, almost perfect. But the other side for some reasons still not right, I have to practice more. My beautiful yarns have arrived and I cant wait.

    Do you have tips for preventing two yarns from getting angled? Thank you for your patience!

  33. purl bee says:

    Hi Sharon.
    I'm glad one edge is looking ship shape. Let me know if you have specific thoughts on the other edge.

    As for the tangling skeins. WhenI work with two I usually keep one in my lap and the other in a little zip pouch. Also with this piece, I found it helpful…. when you turn your work, typically people always turn it in the same direction. To help prevent tangling though, turn it clockwise one row and turn it counter clockwise the next time. That way the two strands won't wrap around one another endlessly.

    Keep us posted on your progress / thoughts on the pattern.

  34. Sharon says:

    Hi Laura,

    I finally figured out how to knit the edges neatly, plus I did seven, yes, swatches, mixing three different yarns and six colors. Now I am ready to start! What I am going to use is Blue Sky Suri Fog and Blue Sky Metalico Cinnabar. The combination is soft and subtle (Cinnabar is very fine), a surprising discovery. If I didnt simply throw them together and tried a swatch, I would have never guessed.

    Thank you for your advice, encouragement and of course, your pattern. Alternating the turns worked too. I dont have a website, when I finish I might try to email you (Soho) a photo.

    Warm regards,


  35. Bristi says:

    Hi Laura,
    What a gorgeous scarf!
    I would like to make a poncho using this stitch/pattern and I have a couple of questions:
    1) I plan to use Purl Soho Worsted Twist (Heirloom White and Timeless Navy)
    I noticed that with the recommended yarn (zageo 6 ply) you sized up by one needle size. Would you recommend that I size up to a size 9 needle with the worsted twist?
    2) When comparing to a stocking stitch, would you say this stitch uses more or less yarn per inch?
    I plan to do a tension square, but any help you can give me would be great. -Thanks.

  36. purl bee says:

    Hi Brisit!
    So glad you like the stitch pattern.
    1. Yes, I would definitely go up in needle size, 1 or 2 sizes, or whatever creates a fabric that is appropriate for your project. This stitch pattern can be quite dense, so going up in needle size lets the stitches breath a bit and makes a drapier fabric.
    2. Yikes, great question. Although I don't really know. I would say yes. It has a very shallow row gauge so in order to get a similar height of fabric it definitely requires more knitting. Do let me know your thoughts on it if you come to any big conclusion.

  37. Sharon says:

    Hi Laura,

    One more question. I love columns of purl bumps on the wrong side, especially the lighter color yarn pops out while the darker recedes. The bumps showed up very nicely in swatches, using the yarns I mentioned in my last post, but when I started knitting full size, the bumps flattened out. I took the fabric off the needle overnight, now the bumps show up better but still not as much as I would like. Do you think I should have used a different size needles, size up or down? Thanks.


  38. purl bee says:

    Hi Sharon.
    Interesting. Fascinating how the fabric responded to coming off the needles. You could go down a size, but I would careful to not make too dense a fabric. Let us know how it goes!

  39. Sharon says:

    Hi Laura,

    Oh boy, I am a little obsessed with this scarf. I dug into my stash, found Madelinetosh Vintage Book Grey. Using Suri Seamist as yarn B, now at 8 long I am totally thrilled! Bumps couldnt be more pronounced, its so much easier to knit than this last one (too delicate looking I admit). Its not dense at all with size 7 needles, and it has the Purlsoho look like yours. Love it, I will go for all the 92 inches! One needs to completely love the outcome to sustain long hours of knitting.

    Again, thank you for your help talking to the designer directly makes it SO special!


  40. Sheila says:

    This is really pretty and I understand the directions when I read. But I have never worked with two yarns… After casting on Yarn A how do you start incorporating Yarn B in the Row 1?

  41. purl bee says:

    Hi Sheila,
    Great question. When you begin working with a new strand of yarn, you simple start knitting with it. Be sure you leave a 6 or so inch long tail so that you can weave in later to secure it. The first stitch is usually a bit loose, but you can usually adjust that when working the next row or by gently pulling your tail.
    Please let me know if you have any other questions. This is a great one and I will add it to our list of tutorials to add to the site!

  42. Rebecca says:

    Hi Laura,

    I just wanted to say thank you for this lovely pattern.
    I made it for my boyfriend for Christmas. At first it was little bit difficult, but then it turned out just perfectly.
    People are even asking my boyfriend at which shop he bought it ;)

    Thank you!

  43. raane says:

    I've finally had a chance to start this scarf, and though it admittedly takes a little while to show progress, I am totally in love with the resulting "fabric." Kudos to you folks for not trying to get a book out of such a lovely and innovative technique ("Weaving Without a Loom for Everyone") and letting the pattern go for free. I am already tempted to try the technique on other garments and I wonder if you or anyone who has used the pattern has adapted the technique to any other items. If so, what and how did it work out?


  44. FiberFollies says:

    I found this when looking for a scarf that would complement a Tychus (knitty). It is a striking knit!

    I CO 60 stitches for an extra wide scarf, forcing the recipient to show both sides when he folded and wrapped it. I also ran a single chain stitch round the edges after knitting it as long as I wanted it. The chain edging covered a few mistakes I made in slipping first stitches from the wrong side. Thank you for this pattern. It really came out well.

  45. Amy says:

    A question about rows 1 and 3. The first stitch is slipped. Then the repeat is p1, sl 1 to end for row 1, and k1, sl 1 to end for row 3. Should I assume the last stitch is slipped too? Row 2 ends with p1. Row 4 ends with k1. Basically we slip the first and last stitches of rows 1 and 3. I just want to make sure I understand it. This may be a beginner's question for reading knitting patterns. Thank you for your help.

  46. purl bee says:

    I am so sorry, I have just now seen this question.
    I have not adapted it to any other pieces, but have been wanting to!
    Have you? How'd it turn out?
    Apologies again for missing this comment. Thank you so much for writing in.

  47. Janine says:

    Hi, I love this pattern but would like to make it into a cowl. Do you have any advice on a suitable type of cast on (provisional?) and bind off, to best meld with the stitch pattern? Thanks!

    • Laura from the Purl Bee says:

      Hi Janine.
      Currently we only have this pattern written for working it flat and not in the round. You could turn the scarf into a cowl by grafting the the two ends together.

      I do appreciate your interest in the pattern and I myself am curious to see how this would look as a cowl. I’ll get it on our list of things to do and hopefully we’ll be able to publish that pattern soon.
      Thanks for writing in.

  48. Gina says:

    I am loving the way this knits up but I have a question about the slip stitches. I’ve been slipping the stitches knit or purl wise depending on which row I’m on:in other words slipping knit-wise on rows 1 and 2 and slipping purl-wise on rows 3 and 4. Is this correct or does it even matter? Thanks in advance!

    • Laura from the Purl Bee says:

      Hi Gina.
      I slipped all the stitches in this project purlwise. I put a note about this in the NOTES section, but it’s often overlooked. Slipping the right side slipped stitches knitwise may cause the fabric to be a bit tighter or denser. Also, the right edge stitch on the right side, may not mirror the left edge stitch if you are slipping the stitches differently on the different sizes. Other than that though… no, there’s no big problem with it at all.
      Thanks for writing in.
      Glad you’re enjoying the pattern.

Leave a Reply

Your email address will not be published. Required fields are marked *

three × 4 =

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>



Subscribers receive a FREE premium Purl Soho Pattern of your choice (up to a $15 value!). learn more